Waterjet Cutting Blog
ITW Formex | Die-Cut/Laser-Cut Parts | Scored, Formed, Bent, Cut
Electrically Insulating materials are a common die-cut product here at NEDC. One of the more common materials we use is ITW Formex. These insulating plastic materials are used in a number of electrically isolating applications. They are flame retardant, and are...
Reinforced Silicone Rubber Gaskets | Silicone Solid, Sponge Rubber
One of the issues in die-cutting is what we call “thin walls” this occurs when there is a hole close to the wall of a part. We typically implore our customers to allow for “break-out” if possible. However, when a gasket is reinforced, it can make this problem easier...
Thermal Insulation | Silicone Foam Rubber Materials
At NEDC, thermal management is close to our core as a company. Most times when companies think of thermal management, they think of Thermal Gap Filler products. The opposite problem to solve is making sure heat doesn’t go in a certain direction. Gap Fillers direct it,...
AquaPro™ PORON® by Rogers Corporation | Water Sealing Polyurethane Foam
At NEDC, watertight seals are a common product we sell. Customers come to us for all sorts of gasketing materials that are good for watertight seals, including silicone rubber, neoprene, and other commonly known gasketing type materials. Separately, customers...
Super-Soft Silicone Rubber Gaskets | Tight-Tolerance/High-Temperature
At NEDC, Custom Silicone Rubber Gaskets are a common product we sell. Included in that category are the Super-Soft Silicone Rubber Gaskets that are available. When I think soft gaskets, typically below 40A durometer would be considered soft. However, when I think of...
Top 3 Reasons to Choose PORON for your Gasket! | Dust Sealing
At NEDC, dust seals, and gaskets are a main product we offer our customers. It can be difficult to find an effective gasket that meets your price range, but is also tough enough to get the job done with little hassle. Luckily, Rogers PORON® gets the job done. In this...
Tolerancing for Thermal Pads | Thickness, Diameter, Linear Dimensions
One difficult thing for the team is when a tight tolerance is put on a thermal interface material. Some of our customers understand, gap filling materials are putty like. Alternatively, thin thermal pads are usually coatings coated on a reinforcement layer such as...
Double Coated Tape by 3M Company | What is a Double Coated Tape?
At NEDC, we use double coated tapes for a variety of purposes. Sometimes we use it as an aid in manufacturing- other times, we provide it to customers either laminated to a gasketing material, or perhaps just the double coated tape itself. What is a Double Coated...
Adhesive Transfer Tapes by 3M | What is an Adhesive Transfer Tape?
At NEDC, one of the main things we do is laminate materials with adhesive backing before we cut them. For this we use 3M Adhesive Transfer Tapes. What is an Adhesive Transfer Tape? Essentially an adhesive transfer tape is a type of adhesive that is coated onto a...
Low Surface Energy Tapes for Gaskets | 3M 300LSE Series Adhesive
At NEDC, gaskets are one of our main product lines. At times the popular tapes that are the “go-to” don’t provide the strong adhesion needed for low surface energy applications. Surfaces that can be difficult to stick to include plastics such as polypropylene,...
Popular 3M Transfer Tapes to Select for your Gasket!
In one of our previous blog posts, we discussed some tips on how to pick a transfer tape for your gasket. One of the tips was, “Make sure you utilize a popular tape if you can.” The reason we said this is, popular transfer tapes are widely available, and their large...
Thermally Conductive Silicone Sponge | Custom Shapes
At NEDC, we are all about thermally conductive gap filling pads. A unique thermal gap filler that can double as a gasketing material is Thermacool R10404 Thermally Conductive Silicone Sponge. This closed-cell silicone sponge rubber gap filling material is not only...
Connector Gaskets | D-Subminiature, M83528/004XDDD
Connector Gaskets describe a type of gasket that has the geometry that would be conducive to a surface found in many connectors. This can be for two reasons. One is the requirement to have an environmental seal. The other being that EMI/RFI shielding capability is...
Thermal Pads | Filling Thick Gaps with Thermal Interface Pads
Oftentimes, customers come to us looking for thermal solutions. The problem with filling thick gaps when trying to solve a thermal solution is many typical thermal interface solutions won’t be a good fit to solve the problem. Reasons other Thermal Management Products...
Oriented Wire Gaskets | Silicone, Fluorosilicone, Silicone Sponge
At NEDC, our main business is die cutting different materials. One material we see often enough is oriented wire lodged in silicone or fluorosilicone rubber material. These materials are referred to as oriented wire gaskets. These wires are oriented 90 degrees against...
Expanded PTFE, ePTFE | Custom Gaskets | Die Cutting
In one of our other posts, we discussed conventional PTFE plastic materials. Generally, we are cutting films, up to .020’’ in thickness. However, when the material is expanded and becomes mostly air, we can cut materials that are much thicker with conventional...
Super-Soft Silicone Foam Gaskets | BF-1000, BF-2000
At NEDC, soft materials are our thing. Actually, soft silicone materials are our thing. These include gap filling pads, gasketing materials, and more. One of the common issues with sealing is the amount of compression force the application can allow. Properties of...
Bonded vs. Waterjet Cut Gaskets | Cost-Saving Techniques
One of the questions we get often especially when it comes to electrically conductive gaskets is “How can I save money on my gasket?” One of the suggestions we have is to allow bigger gaskets to be bonded from more than one piece. This is usually done through bond...
Phase Change Thermal Materials(PCMs) | Die-Cut | Waterjet Cut
At NEDC we are a custom manufacturer of thermal interface pads. Many of these gap filling thermal pads are used to remove heat out of the application. PCM materials offer an advantage that other thermal interface products cannot seem to do. Phase Change Materials work...
Advantages of Thermal Pads over Thermal Pastes
In one of our other blogs, we mentioned other different types of thermal pads and their advantages. Many thermal pads are used as replacements for thermal pastes. However, we never discussed different advantages that thermal pads have over thermal putties/greases. Of...
LCD Gaskets, Touchscreen Gaskets| Dust, Dirt, Water Sealing
At NEDC, we build a lot of types of gaskets. One of the more common types of gaskets we hear of is LCD Gaskets/Touchscreen Gaskets. They are everywhere now, our phones, McDonalds for ordering, and the grocery store. Typically our customers are looking for either dust...
Thin 3M VHB Tapes for Electronics | Die-Cut, Laser-Cut
At NEDC it seems like everything is getting smaller. Gaps to fill, parts to cut, leadtime to place.. Another thing that keeps getting smaller is electronics. With 3M VHB Tapes, there is no problem there. 3M VHB Tapes are used globally, and provide assistance with the...
Military Grade Gasket Materials | Specifications, Reasons to Include One
One of the best things to do when choosing a gasketing material is to pick a military specification to go along with it. There are a few reasons for this: Reasons for Choosing a Military Specification for your Gasket: It makes it recognizable for a lot of suppliers....
Silicone Press Pads, Reinforced Press Pads | Die-Cut
I hope at this point most of our customers at least somewhat think of NEDC when they think of their PCB. We make thermal pads, adhesive preforms, and RF absorbers. However, maybe they don’t think about us when they think of press pads. When PCB laminations are used to...
3M™ Dual Lock™ Tapes | Custom Die Cut Shapes
At NEDC, tapes are a common product we die-cut. At 3M, they are all about fasteners and solutions. They have many solutions for fasteners, permanent, and non-permanent. One of the most prominent fasteners is the reclosable Dual Lock™ Tapes. They are a convenient...
Tips for Choosing a Tape for your Adhesive Backed Gasket!
At NEDC we manufacture a lot of different components for aviation, military, medical and electronics. One of the common things we see is trouble with adhesive transfer tapes. In this blog post, we wanted to discuss some tips on choosing the right tape for your...
Neoprene Gaskets | Sponge, Foam, Solid Rubber
Neoprene(CR) is perhaps the most widely used material in the industry. Any die-cutter is familiar with it. It features an economic cost that matches its versatility. To me, I would call Neoprene the balance rubber. The reason for this is it strikes a good balance...
PGS Thermal Graphite Sheets | Custom Die-Cut Shapes
Thermal management is a core competency at NEDC. One of the core products we die-cut is graphite-based thermal interface material. Panasonic has a line that features incredible thermal performance! Panasonics PGS(Pyrolytic Highly Oriented Graphite Sheet) Thermal...
Soft Gaskets | Soft – Extremely Soft Gasketing Materials
Gaskets come in an incredible variety of materials. One thing about gaskets is it can always get softer. When compression is not an asset, usually the answer is to go even softer. For that reason, I thought I would write a blog about what options are out there when it...
3M 467MP Transfer Tape- Benefits, Availability, Cutting
At NEDC, we laminate a ton of different materials. One of the tapes we use most commonly is 3M 467MP Transfer Tape. We laminate it to thin films, and gaskets to help customers in their assembly process. It is one of my favorite adhesive transfer tapes. In this blog, I...
All of the information presented above is believed to be factual and accurate; however, NEDC is not liable for any design or application utilizing this information.
New England Die Cutting
Capabilities/Products
Quick Links
Popular Blog Posts
Sil-Pad or Gap Pad?
It is easy to understand why the applications of Gap Pad and Sil-Pad can be confused. This is because both thermal pads have a lot of similarities. For the most part Sil-Pads and Gap Pads are electrically isolating. Both thermal pads are thermally conductive, and both...